TP-Link Tri-Band BE9300 WiFi 7 Router Archer BE550 6-Stream 9.2Gbps Full 2.5G Ports 6 Internal Antennas Covers Up to 2,000 Sq. Ft. Add Easy-Mesh Device for Extended Coverage VPN Support

My first review of this product (below) was very negative and deeply sarcastic due to the many issues I was experiencing at the time. Since then, I've gone through many, many hours of troubleshooting, replacing products, replacing all the cable in my house, you name it - only to find that the issue lay with my Motorola cable modem the entire time. (FYI: apparently Motorola no longer makes their own modems; use that information as you will, then buy an Arris.) Since discovering the true source of the problem, this router has performed excellently. And now that everything is actually stable, I've been able to go beyond basic connectivity and finally start digging into the more advanced features of the product. This router has a number of enhancement and convenience features that I never even looked at before. I would strongly urge those that read my previous review to give this device a second look, as I've been able to coax truly impressive performance out of this. I'm leaving my original review up for the lulz, but when reading it, just substitute "Motorola MB8600" whenever you see this product's name. Cheers!---Original review: I ordered the TP-Link AC4000 less than six months ago. Initially, it was decent--good speed, good stability, and the range was a noticeable improvement over my trusty old Tenda. The setup "required" you to install some absurd app, but after some digging, I was able to get to the web interface on the unit and skip taking up yet more space on my phone. After that, setup only took a few minutes, and all was well with the world for quite a while.And then, about two weeks ago, I noticed I had never installed the firmware update. I suppose I'm at least partly to blame here, as I didn't do my usual scouring-the-internet-for-bug-reports before clicking the button. Lesson relearned yet again.I code for a living, but I know very little of what goes into making a firmware build or what the process is like. That said, I understand enough to know that something went very, very wrong with the version I upgraded to ( '1.0.3 Build 20191026 rel.16299' ). The same day as installing it, I started to experience intermittent loss of connectivity, not on any of the wireless networks, but on the connection to the cable modem itself. When it happens, I can't even get to the cable modem's interface to see what's going on there--instead I get some unhelpful message about lost connectivity to the internet (so I need the internet to get to a device in my house. Got it). This is now happening at least twice per day. To top it off, when it IS working, I can no longer connect with my phone when I'm in certain spots in my yard, areas that worked before the update. (I wonder if the range change is some sort of FCC thing, but that wouldn't explain dropping the wired connection to the modem.) When this happens, the only fix is a power-off cold boot, as the 'reboot' function in the menu doesn't fix the issue.I won't go through all the troubleshooting I've done, except to note that once you upgrade the firmware, this device will not let you go back to a previous version. And considering the "current" version appears to be from two years ago, a new update is about as likely as Harvey Weinstein taking back Miramax. I tried a number of tricks to force it but none worked. At this point I should note that, no, I haven't contacted support for this, and frankly, I'm not going to. I don't have hours to spend turning things off and on again while wishing for the sweet release of death, or at least mandatory jail time for whoever it is that records and sells hold music. Plus, I came up with a sort-of-drastic solution that should solve the issue permanently (more on that in a bit).The last straw came yesterday when it dropped connection during a critical server maintenance procedure, literally at the single worst possible moment it could have happened. Fortunately, everything was fine (I was running my code in a Linux screen session, so it kept going), but the two-to-three-minute window waiting for it to come back up was absolute white-knuckle terror, not to mention the post-mortem drudgery of digging through logs to make sure all the steps had completed, as I had output piped to a different terminal, which of course went <poof>. I'm too old for this mess. Since it's outside the return window, *BECAUSE OF COURSE IT IS*, I petitioned (read: "begged") my employer to reimburse me for a Linksys, which is on its way. Meanwhile, it's back to the super-cheap nearly-no-name Tenda, which has worked flawlessly for years now and was only replaced because I upgraded my internet and wanted something faster for working from home, which is very popular lately for whatever reason. Sigh.In summary, if I had the resources to do so, I would build a tiny rocket, strap the TP-Link AC-4000 to it, and launch it directly into the sun, whilst enjoying the fresh spring air with a few close (read: "vaccinated") friends and a glass of something expensive. Alas, I do not. Instead, I'm planning to give it as a Christmas gift to a couple I don't like. I'll flip it upside down, glue a couple of googly eyes on it, and tell their kids it's a robot spider. At least then no one would make the mistake of trying to use it as--shudder--a router.

UPDATE: 23 May, 2024Now it's been awhile. I have to write: If something is messed up, it's NEVER the EAP225 WiFi units or this thing! It's been months since it's been rebooted! We have enough off-grid solar so the internet stuff and the comp room can stay off-grid all the time. It never gets rebooted nowadays and it's always there and it doesn't mess up! It has a gigabit (24 port) switch and two (8 port) 2.5 gigabit switches plugged into it. A total of 4 NAS's; three of them 2.5 gigabit dual LAN's; one with dual gigabit LAN's. And three computers, all 2.5 gigabit. And the Yeacomm 5G gateway is also 2.5 gigabit. Nothing bothers this thing. I'm still not using its WiFi, because of those EAP225's, which are also great. I read a few reviews, before, raving about this thing's WiFi, though and people write that it works great. The wife is Korean and she watches Korean soap opera's all day. We usually download way over a terabyte a month here. The Yeacomm connects at about 400 megabits down and 110 to 130 megabits up.___________________________________________________________________This runs a whole bunch of stuff - WiFi and LAN - typically about 15 devices. I'm not going to rate the Wifi because I'm not going to use it yet. 1) I have two EAP225's; they're VERY strategically located and they mesh with each other. Unfortunately they won't mesh with this thing. 2) I don't have anything else that will even do WiFi 7 yet.I got this mainly for the five 2.5 GbE ports - one WAN and 4 LAN's! I've also got a Yeacomm (Speednet) NR610 (also a very nice, but expensive device), and my internet is blazingly fast! Just very snappy. Internet tasks are usually as fast as doing stuff locally on the computer. You can easily tell when it's the website that's slow. That Yeacomm has a 2.5 GbE port and I was drooling at the thought of getting that 2.5 GbE speed to the LAN. (I also have a gigabit switch, a PoE switch [for the EAP225'sand the Magic Jacks that only do 10 MbE], and two 2.5 GbE switches.) Really nice that all my stuff plugs into this!The WEB interface on this device is a thing of beauty! Everything is very logically laid out, most changes, you don't have to reboot for, and if you know your network stuff, you'll find it nice and easy to use.If you don't know your network stuff, you're still in luck! It took its time communicating with the Yeacomm (LTE CPE Modem) (and a bunch of other devices) on the first boot - maybe 3 minutes or 4 minutes - but it configured itself very well! I have two Magic Jack lines and those didn't work right away. It took some hair-pulling-out time to straighten it out. But I've had one way audio problems with those before. This time, this router had the provisions to fix it (on one of them only.) That's not this router's fault; it's just the way it is. You need to forward a range of ports on two different devices and you can't. It took a very long time to get fixed. It was like a combination lock. Turns out the final step was some settings in the Yeacomm. The Magic Jacks now talk directly to the cell phone tower. One of them works perfectly and the other one only has one way audio when calling [mostly] cell phones. If I had another 2.5 GbE port on the Yeacomm, I could do it, I think, but as long as I can get calls on both lines and call out on one of them, I'm happy.Everything else worked like a champ with settings that this router came up with all on its own! The only thing I changed (not counting the Magic Jack settings) is making a bunch of MAC | IP reservations.When you set it up, you get a light show for awhile. Then the lights can be turned on or turned off with a WEBUI switch. You can also set up a night time mode and have them on in the daytime and off at night, specifying the times. You can plug a USB hdd into the USB port and use it as a very fast, very big network share. It's almost like having an NAS. It's been totally stable and reliable so far.It's a lot of money. I had to talk myself into it. I shopped for about a week. That should tell you something. Now that I've gotten to use it, I consider it well worth the money! I give their tech support 5 stars, not because of this thing, but because I've used their tech support in the past and I already KNOW it's exceptionally good! I have a lot of other TP-Link stuff. Advanced, hi-end stuff.Half of the 12 connected devices shown in the pic.